16 - 18 October 2018 // Nuremberg

Posting print layout

What information should be shown in the print layout?

Create print layout
Zoom product LOGO_Prime Surface Heat Exchangers

Prime Surface Heat Exchangers

LOGO_Prime Surface Heat Exchangers

Prime Surface Heat Exchangers

Request information Request information

Contact us

Please enter your personal information and desired appointment. You can also leave us a message.

Your personal information

Your message for us

Desired appointment during the exhibition

* Compulsory fields you must fill in.
Send
Your message has been sent.

Would you like to use more facilities and advantages of the platform? Then please log in – or register here.

An error has occurred.

PLATECOIL®  Prime Surface Heat Exchanger

Tranter PLATECOIL® Prime Surface Heat Exchangers deliver efficient and uniform thermal control in immersion duty; jacketing vessels, reactors or dryer shells; within fluidized beds or configured as gas phase heat recovery banks. In thermal processing of any kind, PLATECOIL exchangers give you better thermal control than pipe coil, half pipe, dimple sheet or gridcoil (see pipe coil comparison below).

Processors worldwide have used PLATECOIL to:
  • Eliminate sparging for reduced water and steam consumption
  • Capture waste energy from moist, wet flue gases at temperatures as low as 67°C (150°F)
  • Recycle low-grade heat energy from drains
  • Improve economic performance in existing tanks and vessels using clamp-on retrofits
These highly versatile exchangers conform to ISO 9001 standards for design, manufacture and testing for either one-off, special fabrications or high-volume engineered subsystems. Consider all the factors—flow rate, flow balance, heat transfer coefficient, durability—PLATECOIL is engineered and crafted for faster start-ups, constant temperatures, better control and longer service life.

Engineering Shapes PLATECOIL® Efficiency

Essentially two sheets welded together, one or both of which is die-formed, PLATECOIL panels comprise a series of passages through which a heating or cooling media flows. Three styles of Multi-Zone and two styles of Serpentine flow configurations ensure that you get the right combination of flow rate and heat transfer rate with steam, gases or liquids. In designing individual solutions with PLATECOIL, Tranter engineers use advanced computational fluid dynamics (CFD) modeling to determine factors such as heat transfer coefficients and convection effects.

PLATECOIL flow patterns applied for steam provide reserve capacity to compensate for intermittent overloads during start-ups, distributing steam virtually instantaneously to all levels of the plate. Under load swings, PLATECOIL attains desired operating temperatures extremely rapidly, with minimum variation. PLATECOIL styles for liquid heating or cooling media, including hot oil or refrigerants, promote high internal flow velocities for high heat transfer rates.

More than 300 sizes are available, with widths ranging from 305 mm to 1090 mm (12 in. to 43 in.) and lengths spanning 585 mm to 3630 mm (23 in. to 143 in.). A wide variety of materials, gauges and finishes are available. Connection options are 3/4 in. to 2 in. NPT or flange.

Light Gauge, Corrosion-Resistant ECONOCOIL®

ECONOCOIL® hydraulically expanded panels are a special PLATECOIL variant available in an assortment of single-embossed or double-embossed styles and sizes in serpentine or parallel passes. Titanium construction provides long service life where highly corrosive environments exist. Light-gauge titanium ECONOCOIL panels provide better thermal conductivity than units constructed from heavy-gauge material. High turbulence results in low scaling/fouling tendency on external and internal surfaces.

Typical ECONOCOIL Applications
  • Sulfate chrome plating solutions
  • Chromic acid, 10% boiling
  • Nickel plating solutions (except electroless nickel with fluorides)
  • Inhibited sulfuric acid
  • Inhibited hydrochloric acid
  • Hypochlorites
  • Seawater or salt brine
  • Chlorinated hydrocarbons
  • Flue gas heat recovery
  • Stack gas heating

MAXCHANGER® Mini-Welded Plate Heat Exchangers

LOGO_MAXCHANGER® - der geschweißte Mini-Wärmeübertrager

Plate Heat Exchangers

LOGO_Plattenwärmeübertrager

Shell & Plate Welded Heat Exchangers

LOGO_Shell&Plate-Wärmeübertrager

Spiral Heat Exchangers

LOGO_Spiralwärmeübertrager

Prime Surface Heat Exchangers is assigned to following product groups:

There are no entries in your notes.

Show notes



top

The selected entry has been placed in your notes!

If you register you can save your notes permanently and access all entries even when underway – via laptop or tablet.

You can register an account here to save your settings in the Exhibitors and Products Database and as well as in the Supporting Programme.The registration is not for the TicketShop and ExhibitorShop.

Register now

Your advantages at a glance:

  • Advantage Save your notes permanently. Use the instant access to exhibitors or products saved – mobile too, anytime and anywhere – incl. memo function.
  • Advantage The optional newsletter gives you regular up-to-date information about new exhibitors and products – matched to your interests.
  • Advantage Call up your notes mobile too! Simply log in and access them at anytime.